MSDS Type 1 Reinforced
MSDS Type 1 Non-Reinforced
MSDS Terrazzo
Guide To Wheel Grading
FAQ
Safety Guide
Troubleshooting
MSDS Type 1 Non-Reinforced

           MATERIAL SAFETY DATA SHEET


SECTION 1: IDENTIFICATION
          Manufacturer's Name:        Arrow Abrasive and Terrazzo Co.   
             Product Description:         Non-Reinforced Wheels

SECTION 2: HAZARDOUS INGREDIENTS
          
Product may contain any or all of the following:


COMMON NAME      CHEMICAL NAME     CAS#       OSHA PEL    ACGIH TLV     PERCENTS

Alumina                      Aluminum Oxide        1344-28-1        None           10mg/m3             75%

None                         Silicon Carbide           409-21-2          None           10mg/m3              0%

Phenolic Resin            Formaldehyde            50-00-0            2.5mg/m3     .37mg/m3           1/4%
   Liquid                       Phenol                      108-95-2          19mg/m3      19mg/mc

Phenolic Resin         Hexmethylenetetramine   100-97-0         None            None                  16%

Furfural                      Furfural                        98-01-1           20mg/m3      8mg/m3              1/4%

Cryolite                      Sodium                       15096-52-3       2.5mg/me     2.5mg/3               0%
                            Hexafluoroaluminate

Lime                        Calium Oxide                1305-78-8       5mg/m3         2mg/m3          1/2%         

PAF                     Potassium Aluminum         60304-36-1      2.5mg         2.5mg                 8%     
                                    Fluoride

Fibrous Glass                 None                         N/A                 N/A          10mg/m3            0%


SECTION 3: PHYSICAL DATA
      Boiling Point: N/A         Vapor Pressure: N/A     % Volatile by volume: NA
      Water Solubility: N/A         Vapor Density: N/A        Evaporation Rate: N/A

SECTION 4: FIRE AND EXPLOSION DATA
       Flash Point:                        N/A
       Flammable Limits:              N/A
       Extinguishing Media:           N/A     

       Special fire fighting procedures: No special procedures required
       Unusual fire and explosions hazards:   None       
 
SECTION 5: HEALTH HAZARD DATA
       A. Inhalation:      Prolonged exposure to grinding dust may cause respiratory problems or aggravate
                                 existing problems. The dust generated during the use of this products is classified
                                  by OSHA as inert dust or nuisance dust and has the same pulmonary effects of inert
                                  dust.

       B.  Ingestion:       No known adverse effects, but ingestion is not recommended.

       C.  Skin Contact:  Excessive contact with dust may cause skin irritation.
             First Aid:        Wash affected areas with soap and water. Obtain medical assitance.

        D. Eye Contact:   Dust may irritate eyes.
             First Aid:        Flush with large amounts of water. Obtain medical assitance.

SECTION 6: REACTIVITY DATA 
             Stability:                Stable
             Incompatibility:      N/A
             Hazardous Polymerization:         Will not occur.
             Hazardous Decomposition Products:  Dusts are generated in use. In most cases, dust from 
                                                                      will be significantly greater than from grinding wheel.
                                                                      Coolants may produce other decomposition products.

SECTION 7: SPILL AND DISPOSITION PROCEDURES
          Steps to be taken in case of spills: Normal clean-up
          Waste Disposal Method: Standard landfill methods consistent with applicable state and local laws.

SECTION 8: SPECIAL PROTECTION INFORMATION
           Respiratory Protection: Use NIOSH-approved dust respirators as required to maintain exposure 
                                               below Threshold Limit Values (TLVs)
           Ventilation:                   Local exhaust ventilation as necessary to keep dust levels below 
                                               Threshold Limit Values.
           Protective Gloves:         Leather, cloth, or rubber/vinyl gloves as desired by operator.
           Eye Protection:             Goggles or safety glasses with side shields are recommended.
           Other Protective Equipment:    Apron and/or face shields as required.

SECTION 9: SPECIAL PRECAUTIONS
           Avoid breathing grinding dust. Avoid skin and eye contact with grinding dust.
           Handling and storage precautions: Refer to ANSI B7.1 regarding: "Safety requirements for the
           use, care and protection of abrasive wheels.



HomeProductsAbout UsSupportPay HereContact Us